Setting up your Brakes for optimal performance
What not to use or do –
- Car brake cleaner
- Muc-off bike cleaner
- Any other bike cleaner keep it away from your brakes,
- Do not jet wash your brakes cover them.
- leaving moisture to sit on your brakes for days is not recommended
- when riding the brakes will dry from heat, washing and putting your bike away with wet brakes will contaminate pads and can also damage seals – which may cause sticky pistons )
- Resin pads will start to deteriorate with moisture and the compound may part from the backplate.
- Sintered brake pads Can also rust away from the backplate.
- Step 1 remove the calliper from your fork/frame and retract piston with the correct tool
- Step 2 extract old brake pads and clean inside calliper with a dry drag removing any dirt moisture ETC
- Step 3 Pump the pistons out (not too far) and clean around the pistons as much as you can adding a little oil to pick up dirt around the seals and piston carefully push pistons back into the calliper and clean with a dry rag, Repeat this process until pistons are moving free and equal,
- Step 4 Sram brakes/Avid brakes, All brakes can suffer from sticky pistons so making sure the pistons are fully retracted before adding new pads you may need to bleed a small bit of oil from the reservoir to get the pistons fully retracted and mineral oil and brake fluid can expand under heat,
- Step 5 Bleeding your brakes regularly is very important for optimal performance.
- Multi compound Kevlar with Copper
Resin brake pads can make bad brakes feel like they work, Resin is incredibly soft and will bite almost instantly making them easy and quick to bed in but can also mask a weak brake, This will cause premature pads life and uneven braking if the brakes have not been set up properly,
Multi compound Kevlar with copper also a soft compound mixed with kevlar and copper fibres to help brake fade and longevity compared to resin pads, a great all-round compound,
Sintered the full metal brake pad this brake pads will need the brake to be working to optimal performance if you brake are not well looked after fresh bleed and pistons moving freely you will struggle to bed this brake in, un-even piston movement will cause one side (the weak piston) to glaze over this will cause vibrations ending in horrific screeching noises, sintered brake pads are quiet when bedded in properly, Longevity with sintered brake pads is great for winter riding,
Ceramic the lite bite till hot, Ceramic sit between sintered and Multi compound perfect for racing and road bikes as the initial pull from the lever will not lock the brakes making you quicker in the turns, silent braking when Bed in properly,
All compounds have their benefits but if you do not look after your brakes the brake pads will not work properly, Brake maintenance is essential and cleaning and prepping your brakes is overlooked and it should be the most important part of your maintenance schedule,
99% of the time the problem is the brakes, not the brake pads.
if you need any more help please feel free to contact us email@example.com
Bedding Gorilla pads in –
- WARNING: PADS MUST BE BEDDED FOR OPTIMAL PERFORMANCE
- Step 1. On a gradual descending slope, drag each brake for 20-30 seconds, alternating between front and rear. Repeat 3-4 times.
- Step 2. On a hill or steep descent, engage the lever and drag the brakes for 15-20 seconds slowly increasing lever pressure until the bike slows almost to a complete stop. Repeat 3-4 times.
- The front pads will generate more heat than the rear. Once bedded in swap front to rear to create ultimate stopping power.
—— Happy riding Gorilla Brakes ——-
Information above is based on 15 years working with friction material manufactures and hydro brake systems for Mountain bikes, All our products are TÜV Rheinland tested for your safety .
TÜV Rheinland is a leading provider of technical services worldwide. Founded in 1872 and headquartered in Cologne, Germany, TÜV Rheinland employs 20,000 people in over 65 countries. The group provides a broad range of testing, inspection and certification services to ensure the safety, reliability and regulatory compliance of assets and components throughout their lifecycle; as well as technical consulting and training to industrial, transportation, products and healthcare sectors. For over 145 years, we have been developing solutions to ensure the safety and quality of the interaction between man, technology, and the environment. We firmly believe that social and technological progress are intrinsically tied together.
The Group’s mission and guiding principle is to achieve sustained development of safety and quality in order to meet the challenge arising from the interaction between man, technology and the environment.