Measuring Pad Wear. Brake test rig used to compare Factory Racing Stealth and Enduro Pro Semi Metallic pads.

Brake pad wear test | Enduro Pro Semi Metallic vs Factory Racing Stealth

Work in progress: these are early results from tests we're still running on our rig. They are not final data, and the numbers may change as testing continues.

Factory Racing Stealth wore faster than Enduro Pro Semi Metallic in this test. For the same amount of braking work, Stealth used about 78% more of its starting friction material. We compared the share of each pad worn away because the two sets did different amounts of braking.

How the brake pad wear test works

Adam Read carried out all the testing for this series.

  1. Spin the disc and apply the brake. The rig turns a brake disc. When the brake is applied, the pads squeeze the spinning disc, just as they do on your bike. As the pads rub against the disc, some of their friction material wears away.
  2. Record how much braking the pads did. We add up the braking work over the whole run. We measure it in kilojoules, shortened to kJ. We then look at how much of the pad material was used up over that same run.
  3. Compare an equal share of each pad. Picture the friction material on a fresh pad as 100 equal squares. One square represents 1%. We use the figures from each whole run to work out how much braking each pad did per square worn away. A higher number means more braking for the same share of pad used.

Brake pad wear results per 1% of material lost

Factory Racing Stealth did more braking work in total during its run. The last column shows how much braking work each pad did per 1% of friction material lost. A higher number in this column means better wear resistance.

Compound Braking work Material lost Work per 1% lost
Enduro Pro Semi Metallic 72.98 kJ 1.767% 41.30 kJ
Factory Racing Stealth 82.04 kJ 3.53% 23.2 kJ
Braking work per 1% of friction material lost on the rig. Enduro Pro Semi Metallic 41.30 kJ and Factory Racing Stealth 23.2 kJ.
Braking work per 1% of friction material lost in these rig tests. A longer bar means the pad did more work for the same proportion of material used.

How we calculated wear resistance

Take Enduro Pro Semi Metallic. The rig recorded 72.98 kJ of braking work and the corrected material loss was 1.767%. Dividing 72.98 by 1.767 gives 41.30 kJ per 1% of pad material lost. The same calculation for Factory Racing Stealth gives 23.2 kJ. That’s where the ratio of about 1.78 comes from.

What the wear test tells riders

Ride a mile along a flat lane and you might barely touch the brakes. Ride a mile down a steep, twisting trail and you could spend much of it on the levers. Both add a mile to the bike computer. That’s why “How many miles will these pads last?” is such a tricky question to answer.

Enduro Pro Semi Metallic took more braking work to wear away the same share of its lining in these tests. How far a set takes you on the trail will also depend on how often you brake and how much mud and grit get between the pads and disc.

What we know about rotor wear

The rotor has its own wear story. The Factory Racing Stealth test recorded 60 mg of material lost from the rotor. We still need the corresponding measurement for Enduro Pro Semi Metallic before we can compare the two on rotor wear.

How we’ll check the wear results

These runs are part of our ongoing test programme. We’re still developing the wear test protocol, including how we record the material each set loses and match it to the braking work over the same runs. If a change to the method affects the comparison, we’ll explain it alongside the updated figures.

For these runs, we have the reported wear percentages but no original pad measurements to check them against.

We want to put a fresh set of each compound through the test and see whether the gap repeats. We’ll keep the starting and finishing pad measurements with the energy log for those exact runs, including any bedding that counts towards wear. That gives us a way to see how much the result varies between sets.

Brake pad compounds tested

Related brake pad tests

Browse the brake rig tests

This testing is still underway. We'll update this post as more results come in. The figures here are not final.

Back to blog

Leave a comment

Please note, comments need to be approved before they are published.